Easy Burlap Window Shades

Easy Burlap Window Shades

Some of you know I’ve been working on building my she-shed and I’m finally getting to the fun part, the decorating!  Today I've been working on the window coverings.  My Easy Burlap Window Shades were pretty easy to make.  I have basic sewing skills, as long someone loads the bobbin thread for me ;) but for this project, I called in the big guns, MOM! 

 Here’s what we used:

  1. Burlap Fabric
  2. Sewing machine, scissors, pins and thread
  3. Heavy Duty Stapler
  4. Thin strips of wood. 1/4” thick x 1 1/4 “ wide x by the width of the window
  5. Hammer and nails (drill and screws work, too)

Here's how we did it:

After we determined the finished shade size, we added 4 inches to the width and 7 or 8 inches to the height.  Here’s why:

My window is 72” wide so I cut the fabric width to 76”.  We turned the fabric over one inch, then another and stitched it down so the edges of the burlap will be hidden and won’t unravel over time.  That’s where you get the extra two inches on each side.  As a tip, my mom came up with the idea of using a piece of cardboard that was cut into a 1 inch strip to use as a guide for the side folds.  She wrapped the fabric over the cardboard one inch and then folded it again and pinned the fabric in place then kept sliding the cardboard out as she worked her way down the side.  I hope that makes sense...  You can also iron a crease for the first inch and then fold and iron again and then secure it with pins before you sew.

The part of the project that took us the longest was getting the burlap cut straight.  We tried methods we’d read from others like pulling a string out to create a straight line and it honestly didn’t work for us.  What finally worked was laying the burlap on my wood floors and using the line in the wood to get things straight.  Once you get the burlap fabric cut, the rest is pretty easy.

burlap window coverings

(This is a sample of how the finished side hem looked)

The height of my window is 36” and I wanted a 3” hem.  Again, we turned the fabric one inch, then three inches and sewed the hem.  You’re still going to need a few extra inches at the top to attach the shade to the board.  More about that later.

Once you’ve sewn the sides and the hem, you’ll be ready to attach the shade to the thin strip of wood.  We laid the shade out flat on the floor and measured from the bottom of the shade to the height that we wanted the finished window covering to be and marked it with a straight pin on both sides.  Place the pre-cut piece of wood on the shade so that the top of the wood is aligned with the two pins.  Now gently and evenly flip the wood piece towards the top of the shade two times.  You won’t pick the wood up.  Just hold it down to the ground and flip it two times.  Have someone help you hold the wood in place while you cut the fabric off so you have about 1” sticking out the top of the wood piece. 

burlap window coverings

In the picture above,  you'll see the fold over the wood.  This is where you'll want to staple the fabric to the wood strip all the way along the strip.  You may have to use a hammer to tap the staples in all the way if they don't cooperate.  You'll want the staples flush.  See the frayed fabric edge, since I didn't take a picture of this project along the way, you'll have to pretend that the frayed part is your finished bottom hem.

Now, roll the wood up in the fabric by flipping it back towards the bottom of the shade two times.  This is when you’ll want to hold the shade up to the window to see if you got it right.  Hopefully all is good!  Now, have someone help you hold the shade up to the window frame and lift the shade over your head and hammer nails into the wood strip.  You’re doing this so you don’t nail directly through the visible part of the shade. You can see that my shade is attached directly to the front of the wooden window frame.  If you have to install yours inside the window sill, you'll have to rethink the measurements so keep this in mind.) 

easy Burlap window shades

Holy moly, the shed window is dirty!  

I originally wanted a roman shade, but my shed is tongue and groove and I already have so many horizontal lines to deal with so that’s why I opted for this simple design.  I also didn’t know if I’d have the patience for attaching the strings. (that's the real reason!)  Instead, I attached small silver washers to the bottom corners of the shade and one in the center.  I installed small white cup hooks that blend well with my white paint at the top of the window.  When I want to open the shade, I just hook the washers onto the cup hooks. The second cup hook hanging out there on the side was a failed attempt.  Oops.

burlap window shades

Did you notice the old door knobs I used in the final picture?  I am in love and if you want to see how I did it, you can read this post about Door Knob Window Decor.

If you use any of my ideas, please mention Hootshack in your post or pics.  Also, if you try this at home, share your own photo on Instagram and use #HootshackDIY so I can see.  Also, don't hesitate to send pictures and details about your projects.  If you do, I may share them with my readers.  You can use the Contact page to reach me!  Please share, pin, tweet or whatever you do!  ;)

Have a great day friends!

Xoxo,

Denise


1 comment

  • You truly know how to bring out the beauty in burlap! Can’t wait to start more projects that you have inspired me to do!

    Katie

Leave a comment

Please note, comments must be approved before they are published